Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to auto locksmiths with experience who have the appropriate equipment and know-how. They will be able to create and program new keys much quicker than a dealership and at a lower cost.

If your key fob has stopped locking or unlocking your doors, it is likely due to a dead battery in the coin. There are also other reasons that the key could be malfunctioning.

Dead Coin Battery

A dead coin battery will hinder your Peugeot 208 from locking or unlocking, and cannot start the engine. If this is the scenario, you'll need apply the backup starting technique that is detailed in the owner's manual to your vehicle.

The spark plugs can also be worn out. The spark plugs are responsible for instigating the fuel which starts the engine. However, they have a limited time of life. If they aren't used enough they will eventually fail.

Fortunately, there's an easy solution for this issue. The best way to solve this issue is to check the voltage of your car battery with a multimeter. If it's lower than 11.5 volts then you must replace it. It is also essential to clean the contacts of the battery when it has corrosion. This can be accomplished by removing the rubber covers from the two battery terminals and then using a wirebrush, you can remove any corroded battery parts. Then, reconnect the cables to the positive and negative poles.

Water Damage

If your 208 will not start and the battery hasn't fallen flat, it is time to inspect the spark plugs. You may find that they're filthy and don't spark. The spark plugs can be cleaned in a workshop.

Peugeot cars use a key with a transponder compatible with the immobiliser. This guarantees that only the right key can start the engine. If the chip inside the Peugeot key is damaged, it won't send the proper signal to the vehicle.

This is a common problem that can be caused by water damage. This is a frequent issue in colder climates where the vehicle has been exposed to rain or snow. In this case, you need to contact a reliable locksmith who has the required tools and equipment to reprogram the key. They also have the latest technological know-how and the equipment required to make a Peugeot 208 smart key. The process should not take more than 15 minutes.

Contacts of the battery may be damaged.

Peugeot replaced the transponder chips with a brand new type that uses electronic components mounted on a circuitboard. The new system is effective when it's brand new but over time the circuit boards begin to deteriorate and stop working correctly.

This could prevent the immobiliser chip from triggering which means that your car won't start. Contact a Peugeot specialist or a locksmith, if this is the case.

A common issue is when the battery in the key fob starts to fail. This causes the blade of the key to stop feeding into your lock. A locksmith for cars will replace the battery and cut a new blade for you. This is a quick solution.

Faulty Receiver Module

If your Peugeot key fob stopped working after dropping it on the floor, being exposed to a sudden downpour or accidently washing it or washing it, it could be due a malfunctioning receiver module. The receiver module is responsible for transmitting radio signals to the onboard computer which regulates the central locking system of your Peugeot vehicle.

Rubber seals on the key fob prevent water from reaching the electronic chip. Water can damage the chip in the event that it is exposed the water for an extended period of time. Submerging the key fob in sea water at the beach or throwing it into the water can be especially damaging because of the high salt content.

The module must be replaced if the Peugeot spare key no longer works. This can only be done by a skilled auto locksmith or peugeot boxer key specialist. Like other automobiles, peugeot 107 key fob replacement keys are protected by an exclusive immobilizer system that requires the right coding for the start of the engine. This is why you should go with a knowledgeable Peugeot locksmith for the job of programming and creating an appropriate replacement.

Faulty On-Board Computer

The computer on the board of your peugeot partner van key is responsible for many of the systems inside your vehicle, from airbags to power windows. The on-board computer will show a code when something goes wrong. This code will be saved within the system until the issue is fixed. In most cases, this will require replacing the computer on board.

One of the most frequent causes of the airbag light flashing is loose or corroded connections in the airbag sensor. This can be caused by wear and tear, aging, or exposure to salt and moisture. It is important to have this issue addressed as soon as you can, as an airbag that is not functioning properly could be dangerous in the event of an accident.

If you notice an error message stating that the card is not found on your Peugeot, the key battery inside the key fob might be dead or weak. This prevents the key fob from transmitting a signal that will disable the standard immobilizer in your vehicle. You can test this by pressing the unlock button on the key fob and then trying to start your vehicle. If this fails then the battery in the key fob is in need of replacement.